Output chart. Voltage too low. Circuit breaker trips. This manual is also suitable for: Print page 1 Print document 10 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Upload from URL. Before using, the user shall determine the suitability of this product for its intended use and assumes liability therein. Contact NorthStar Product Support at for any questions about the appropriate use of this generator.
Please fill out and submit the warranty registration card so that we have your contact information for any future product literature or replacement parts you may need.
Caustic acid and explosive gases can cause blindness or severe burns. NO smoking, sparks, or flames. NEVER touch both battery terminals at the same time with your hand or any non-insulated tools.
FLUSH immediately with water if battery acid contacts eyes, skin, or clothing. NEVER charge a visibly damaged or frozen battery. A charged battery ensures reliable engine starting. Always make sure safety labels are in place and in good condition.
If a safety label is missing or not legible, order new labels or unsafe operation could result. To order replacement safety labels , call NorthStar Product Support at Large tank allows for extended run capabilities. Before using your generator, determine the running and starting wattage requirements of all the electrical devices you will be powering simultaneously.
The sum of the running and starting wattages of the devices being powered must not exceed the continuous output rating of your generator. Note that:. If only the running voltage is given on the nameplate for a device with an electric motor, the starting wattage can be approximated to be three to five times the running wattage. Estimates for the running wattage requirements for common devices are listed in Table 1 below.
To calculate the running and starting wattage requirements for the devices you will be powering, follow these steps:. Make a list of all electrical devices you will be powering at the same time with the generator.
If only the running wattage for a device with an electric motor is known, the starting wattage can be estimated to be at least 3 times the running wattage. Add the wattages for all devices on your list. This total must be lower than the continuous output rating of your generator. In this example, the generator must have a continuous output of at least W in order to power all of the devices simultaneously. You can increase the number of devices your generator can power by staggering the load on the generator.
For example, you could alternately power your refrigerator and air conditioner for limited periods of time -- powering only one of the devices at a time and never powering both at the same time.
There are a number of important steps required to set up your generator for initial use. These steps are:. Setting up generator for the type of power generation you need:.
Selecting a site for using the generator. Battery installation electric start models only. This generator is designed to provide up to W of electrical power.
It can supply electricity in two ways:. The transfer switch must be installed in accordance with building electrical code and guidelines supplied by your power company. Note : Regardless of whether you use your generator as a back-up power source connected to a building or as a portable power source, you must not overload the generator.
Overloading may cause serious damage to the generator and attached electrical devices. Contact a licensed electrician to install an UL-approved transfer switch if you want to use your generator as a back-up power source for a building.
A transfer switch must be installed in order to isolate your generator from the utility power grid. If your generator is NOT properly isolated from the utility system, serious hazards will arise:. The transformer will step up the current to the normal line voltage. An unsuspecting utility line worker working on what he thinks is a deactivated line could be electrocuted. It could also explode or cause fire.
In addition to isolating your generator from the utility system, the transfer switch connects your generator to a limited set of circuits in your building that have been chosen as critical to operate during a power outage. The electrician can help you determine which circuits and devices can be powered simultaneously without overloading the generator. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox.
Please check your email for further instructions. Enter a new password. North Star. Thank you for purchasing your NorthStar portable generator! About Your Generator This engine-driven, portable generator is designed to provide up to Watts of electrical power watts continuous, watts surge. It can supply power: 1.
Overloading will cause damage to the generator and attached electrical devices, and may also result in fire Be sure to read about site selection and grounding requirements for running this generator.
Warranty Registration Please fill out and submit the warranty registration card so that we have your contact information for any future product literature or replacement parts you may need. Figure 1 Ref. Description Ref. However, only half the power or watts Reference 4 — Voltmeter Voltmeter needle should be in green area during all generator load conditions.
With no load Switch on the generator the engine speed drops to idle. This saves fuel and lengthens engine life. When a load is applied, the engine speed returns to - RPMs. Turning the switch off disables the sensing device and the generator will run at - RPM whether or not a load is applied. Note: When the engine is idling, it is normal for the voltmeter needle to be in the red range.
Reference 6 — Hour Meter Allows for better maintenance scheduling of generator. Reference 7 — Main Line Circuit 30 amp A magnetic 2-pole main circuit breaker to protect Breaker 30A against electrical overloads. You can monitor the fuel level without removing the cap by using the fuel level indicator built into the gas cap. Reference 12 — 6. Reference 14 — Generator Head The electricity producing part of the generator. Reference 15 — Battery Box The battery box provides protection for the battery and will accept a standard lawn tractor size battery Group U The engine requires a volts battery, with a minimum rating of 18Ah Amp-Hour.
See battery section for sizing. Reference 16 — Vibration Isolation The engine and generator are mounted on rubber cylinders Mount that absorb most of the engine vibration. Reference 17 — Recoil Grasp firmly when starting engine.
Consult engine manual for further instruction. Reference 19 — Choke Lever Used during cold starts. Reference 20 — Engine Starting Key The engine key is located on the engine.
Always locate this switch and be familiar with its location before operating the generator. Setting up generator for the type of power generation you need: a.
Each of these steps is discussed in detail below: 1. It can supply electricity in two ways: 1. Specific requirements for each are given below.
Using as a Back-up Power Source for a Building.
0コメント